ResinTech TUE Transparent Epoxy Base Coat - Canopus Supply Inc

ResinTech TUE: Transparent Universal Epoxy (100% Solids)

$238.00

Type:

TUE (15 L/4 Gals)

Variant

Description

✅ Usually In Stock, North Vancouver, BC. Call 250-233-3000 to confirm availability or arrange pickup.

ResinTech TUE — 100% Solids Transparent Universal Epoxy

Field	Details
Brand	ResinTech
Product Code	TUE
Product Type	100% solids transparent universal epoxy (primer / build / broadcast binder / self-level)
Kit / Pack Size	15 L kit Part A 10 L + Part B 5 L (4.0 US gal mixed)
Colour / Finish	Clear, glossy with a slight satin sheen; field-pigmented when approved
System Role	Premium epoxy reinforcement / build layer may substitute for CBE

ResinTech TUE is a 100% solids, two-component transparent universal epoxy for commercial and industrial concrete floor systems. It is used as a primer, reinforcement / build coat and broadcast binder for flake, quartz, metallic and solid-colour systems, and as the premium epoxy layer in ResinTech traffic coating systems, where it may be substituted for CBE. For UV-exposed or exterior applications, specify a UV-stable aliphatic topcoat such as ResinTech HPP polyaspartic topcoat, TCU aliphatic urethane topcoat, or CRU chemical-resistant urethane topcoat where required by the system design.

Where TUE sits in the system: In ResinTech traffic systems (PTS / VTS / EWS), TUE is the premium epoxy reinforcement / build layer and may be substituted for CBE where a premium epoxy is preferred. It is protected by an HPP UV-stable surface coat (or a CRU premium finish); where movement or waterproofing is required, a FLEXCOAT-PU flexible base membrane is used beneath the build. Confirm the system specification against the current ResinTech documentation. View the full range of ResinTech floor coating systems available at Canopus Supply.

Best-Use Applications

Confirm all applications against the current ResinTech TDS before specifying.

Parkade decks and ramps
Exposed balconies and podium slabs
Commercial and industrial concrete floors
Flake, quartz, metallic and solid-colour broadcast systems
Pedestrian walkways and stairwells

Product Data

Source: ResinTech TUE Technical Data Sheet (TDS-TUE-1.0). Typical values at 23 °C and 50% RH unless noted. Confirm against the current TDS before specifying or ordering.

Property	Typical Value	Note
Components	Two — Part A resin + Part B hardener	Mix full kits where possible
Mix Ratio	2:1 by volume (Part A : Part B)	—
Solids Content	100% by weight	—
VOC	< 50 g/L	Effectively VOC-free for a 100% solids epoxy confirm against SDS
Appearance	Clear or pigmented	Clear resin may appear slightly amber in mass
Odour	Low	Use ventilation during application
Induction Time	None	Apply immediately after proper mixing
Shelf Life	10 months	Unopened, stored properly at about 25 °C
Storage	Sealed, cool, dry, ~25 °C	Protect from freezing, heat, moisture and direct sunlight

Performance Properties

Typical values from the ResinTech TUE TDS. Actual results depend on substrate, preparation, mixing, film build and conditions — confirm against the current TDS.

Property	Typical Value	Test Method / Note
Bond Strength to Concrete	370 psi	ASTM D4541; typically concrete cohesive failure
Tensile Strength	6,500 psi	ASTM D412 / D638
Elongation	6%	ASTM D412 / D638
Abrasion Resistance	35 mg loss	ASTM D4060, CS-17 wheel, 1000 g, 1000 cycles (excellent for an epoxy)
Shore Hardness	80 D	ASTM D2240
Tack-Free Time	10 hours	ASTM D1640 at 15 mils
Drying Time	20 hours at 15 mils	ASTM D1640, 24 °C / 50% RH
UV Resistance	UV-resistant epoxy	Not a UV-stable aliphatic topcoat; use HPP/CRU for permanent unprotected UV
Chemical Resistance	Excellent	For severe chemical service, topcoat with CRU confirm against TDS

Working Time, Recoat & Cure

Times vary with temperature, film build and conditions. Large mixed volumes shorten pot life and can create heat. Confirm against the current TDS.

Temperature	Pot Life	Recoat Window	Light Foot Traffic	Full Cure
10 °C	60–75 min	18–24 h	36–48 h	~10 days
21 °C	40–60 min	14–18 h	~24 h	~7 days
30 °C	20–30 min	8–12 h	12–18 h	4–5 days

If the surface is hard, glossy or outside the recoat window, sand / abrade, vacuum and clean before recoating.

Coverage & Film Build

Per US gallon. A 15 L kit is approximately 4.0 US gal. Actual coverage varies with profile, porosity, film build and method — confirm against the current TDS.

Use	Typical Film / Build	Typical Coverage
Primer / Base Coat	8–10 mils	200–160 ft²/US gal
Top Coat	8–16 mils	245–120 ft²/US gal depending on profile and build
Broadcast Receiver	10–25 mils before broadcast	145–80 ft²/US gal plus aggregate
Self-Levelling Build Coat	40–250 mils in controlled pours	By design and mass control

Application Conditions

Confirm all conditions against the current ResinTech TDS and project specification before use.

Condition	Requirement
Substrate Temperature	10–30 °C
Ambient Temperature	10–32 °C
Relative Humidity	Maximum 85% recommended
Dew Point	Substrate at least 3 °C above dew point
Concrete Moisture	Dry concrete; typical screening limit 4% Tramex or 85% RH by ASTM F2170
Concrete Age	Normally 28 days unless the designer approves earlier work
Minimum Concrete Strength	3,600 psi compressive and 220 psi tensile pull-off

System Compatibility

Confirm all system combinations against the current ResinTech TDS and project specification before use.

System Layer	Compatible Products
Flexible Base (movement / “+” systems)	ResinTech FLEXCOAT-PU flexible base membrane, beneath the build — confirm against TDS
Reinforcement / Build	TUE may substitute for ResinTech CBE as the premium epoxy build layer — confirm against TDS
Surface / Topcoats	ResinTech HPP (UV-stable polyaspartic surface), CRU (premium chemical / UV finish), TCU (aliphatic urethane) — confirm against TDS
Not Recommended For	Immersion service; exterior or UV-exposed applications without a compatible UV-stable aliphatic topcoat — confirm against TDS

Application Notes

Always confirm application requirements against the current TDS, SDS and project specification before use.

Surface Preparation

Concrete must be sound, clean, dry and free of laitance, curing compounds, sealers, oil, grease and bond breakers. Mechanically prepare to ICRI CSP 2–3 for thin coatings and CSP 3–4 for broadcast or traffic-duty work. Vacuum until dust is removed from pores and profile; do not rely on acid etching for professional work. Repair cracks, spalls, joints and edges before application; dynamic cracks and movement joints require separate detailing. Test existing coatings for adhesion and compatibility. Do not apply to wet concrete, condensation or active water intrusion — TUE is not a moisture-vapour mitigation system. Confirm all requirements against the current TDS.

Mixing

Condition materials to application temperature before use. Pre-mix Part A; add compatible pigment to Part A first when a pigmented coat is required. Add Part B at 2:1 by volume and mix mechanically for 3–5 minutes at low speed. Scrape sides and bottom of the pail and avoid whipping air into the resin. Do not thin with solvents. Use full kits or accurately measured partial kits. For deep-build or casting work, pour promptly after mixing and control mass to limit heat. Confirm mixing procedure against the current TDS.

Application Tools

Apply by squeegee, roller, notched squeegee or gauge rake and backroll to an even wet film, maintaining a wet edge. For broadcast systems, broadcast quartz, flake or sand into the wet TUE at the specified rate and remove loose media after cure. Confirm recommended tools against the current TDS.

Finish & Gloss

TUE cures glossy with a slight satin character from its additive package, rather than a mirror-like super high-gloss. Where a super high-gloss finish is required, ResinTech recommends CBE (Core Bond Epoxy). Colour, clarity and gloss can vary with film thickness, mass, temperature, substrate and pigmenting method.

Limitations

UV-resistant, not a UV-stable aliphatic system; under prolonged unprotected UV it can amber or lose gloss — topcoat with HPP or CRU for permanent exterior UV.
Not a crack-bridging membrane and not for active cracks, moving joints or structural movement.
Not a waterproofing membrane or moisture-vapour mitigation system.
Deep pours are for experienced installers only — do not attempt large-volume casting without a mock-up and heat-control plan.
Do not apply to wet, frozen, contaminated, dusty or condensing substrates.
For severe chemical service, protect with a CRU topcoat — confirm against the TDS.

Frequently Asked Questions

What systems is TUE used in?

TUE is the premium epoxy reinforcement / build layer in ResinTech traffic systems (PTS, VTS and EWS), where it may be substituted for CBE, and the epoxy build layer in flake, quartz, metallic and solid-colour floor systems. See the full range of ResinTech floor coating systems at Canopus Supply. Confirm system design against the current ResinTech TDS.

Does TUE yellow under UV exposure?

TUE is more UV-resistant than ordinary epoxies and resists yellowing better than standard epoxy, but it is not a UV-stable aliphatic system. For long-term colour stability in UV-exposed or exterior applications, use a compatible UV-stable aliphatic topcoat such as ResinTech HPP, TCU or CRU. Confirm system suitability against the current TDS.

Can TUE be used on exterior surfaces?

TUE may be used in interior and protected exterior assemblies; for permanent unprotected exterior UV exposure, specify a UV-stable aliphatic topcoat over it. Confirm suitability against the current TDS and project specification.

How do I get a super high-gloss finish?

TUE cures glossy with a slight satin character. For a mirror-like, super high-gloss result, ResinTech recommends CBE (Core Bond Epoxy). Confirm finish expectations against the current TDS.

Where can I buy ResinTech TUE in BC?

ResinTech TUE is stocked at Canopus Supply in North Vancouver. Available for pickup or delivery across British Columbia. Call 250-233-3000 to confirm stock or arrange a volume order.

Technical Documentation

Technical Data Sheet (TDS) — ResinTech TUE
Safety Data Sheet — Part A — contact Canopus Supply
Safety Data Sheet — Part B — contact Canopus Supply

Download the ResinTech TUE Specification Sheet

Full technical data for specifiers and contractors. Confirm all values against the current TDS before use.

⬇ Download TDS (PDF)

Trade Purchasing Note

All sales are intended for professional and trade purchasers. Before ordering, confirm product suitability, quantity, colour, system compatibility, substrate condition, pickup timing and delivery requirements. Product use and installation are the responsibility of the purchaser and installer.

Technical information is provided for professional reference only. Product selection, substrate preparation, installation method, coverage, cure time, system compatibility and final performance remain the responsibility of the purchaser, installer, project specifier and/or manufacturer documentation. Always confirm suitability against the current TDS, SDS, project specification and site conditions before use.

Order Enquiries & Volume Orders

For volume orders, system compatibility questions, pickup timing or delivery across BC, contact Canopus Supply before placing a bulk order.

Call: 1 (250) 233-3000
Email: order@canopussupply.com
Pickup: Unit 103, 185 Forester Street, North Vancouver, BC

Canopus Supply Inc. — Authorised ResinTech Distributor, Metro Vancouver & BC

ResinTech TUE: Transparent Universal Epoxy (100% Solids)

$238.00

Pickup & BC delivery

Contractor pickup in North Vancouver or delivery across British Columbia.

Secure payment

Checkout is encrypted and secure on every order.

Contractor accounts

Volume and trade pricing for contractors and commercial accounts.

Easy customer support

Call, WhatsApp or email us — real people, fast answers.